Posted on

ENERGY METER SINGLE PHASE 63A BY EELECTRON

• This Energy-meter provides the essential measurement capabilities required to monitor a single phase electrical installation.

• 0.25-5 (63) A, Class B, 230 VAC 50 Hz, -25 °C … +55 °C, 4 Quadrants, 2 Tariffs.
• Active Energy Class B (according to EN-50470) and Reactive Energy Class 2 (according to IEC 62053-23)
• Direct connected (up to 63 A)
• LCD display and 3 push-button keys (to read Energies, V, I, PF, F, P, Q and to configure some parameters)
• 1 push botton and 1 LED dedicated to KNX.
• Display with 8 digits.
• Self supplied (by the input voltage itself).

Device is intended to be installed on DIN rail.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

ENERGY METER 3P WITH TA CONNECTION – BY EELECTRON

This Energy-meter provides the essential measurement capabilities required to monitor a three phase electrical installation.
• Three-phases digital energy meter with connection by CT …/1 A up to 2000/1 A or by CT …/5 A up to 10.000/5 A 0.01-1(6) A – 2 Tarif
• LCD display and 3 push-button keys (to read Energies, V, I, PF, F, P, Q and to configure some parameters)
• 1 Push button and 1 LED dedicated to KNX.
• Display with 8 digits.
• Self supplied (by the input voltage itself).
•1 S0 pulse output proportional to Active Imported KWh
Device is intended to be installed on DIN rail.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

TRANSPONDER READER KNX BY EELECTRON

The TR22A01KNX card reader is an KNX device dedicated to access card control with the transponder; it is customizable versatile and modular, and suitable for almost any application. Mounting boxes are embedded, rectangular or round with 2 or 3 modules. Different color ranges available and glass finishes can be ordered separately, allowing the unit to be matched with every kind of design. The device has two physical ON / OFF inputs available for controlling the door open / close contacts or other signals (window contacts, bathroom pull alarms etc.). The device has two relays for lock management, courtesy light control or another use. On the reader front there are 4 LEDs, 3 of which are freely configurable, and used respectively for the reporting about: access granted, access denied, emergency, required room redo, room occupied or do not disturb. The transponder reading can be made at a distance of 30 mm. The primary feature is the number-control facility. If the code is consistent, the device will continue by verifying the validity of the “date” field (if enabled). Then the “password” will be checked with the associated codes with it (hours, customer number, service number), and enabled. If verified, the door will open, and (if set), the courtesy light will be turned on, and the reading will be forwarded to the bus. ETS configuration.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

TRANSPONDER READER KNX

The Transponder Reader TR32Ax9KNX is 2 IN / 2 OUT + BELL and a KNX wall mounting device suitable to access control application.
This device can be used in any kind of building (Hotel, Hospital, Offices, Parking, etc..) where the access control application is required.
The device is equipped with two binary inputs (potential free contacts) that can be used, for instance, to control whether the door lock has been opened or closed or other signals coming from external switches/contacts (i.e. windows, bathroom emergency alarms, etc..) and with one frontal switch freely configurable by ETS. The transponder reader is equipped also with two output relays which can be used for any purposes, typically to open the door or turning on the courtesy light inside the room.
The product provides on the front side four LEDs in order to enlighten 4 icons to display the following states (e.g. in case of Hotel management):
– Access Allowed/Not Allowed
– SOS request
– Service Call (clean room, etc..)
– Client status (“Busy room” or “Do not Disturb”)
The LEDs and icons can be configured in association with other alarms or events. The transponder reader can reads cards or keys at a maximum distance of 30mm from the front side.
The access control follows a sequence where the “build number” has been checked at first, then the “data” to check if it has been elapsed or not, next the password ID for client/ guest/service identification, then the enabled entrance timing window. In case card reading pass all checks the door is opened and, if set, the courtesy light inside is switched on. At the same time the Transponder Holder can send the reading response to the bus.
The device configuration for commissioning in terms of physical address, group addresses and parameters is done with ETS ( Engineering Tool Software) through a download of the Application Program.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

TRANSPONDER KEYHOLDER

Dimensions and characteristics of Key chains
Dimensions and Material: ABS 38 x 34 x 6 mm
Frequency: 125KHz –
Operational temperature: -10 ° C to 50 ° C
50 PCS

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

VIRTUAL BADGE – HORIZONE WEBSERVER by Eelectron

Virtual Badge is an innovative access control system, which allows the opening of door locks with your smartphone, without the need for keys or badge readers physically installed in front of each door.
The management of permission of the users, and the sending of virtual access keys, is entirely manageable via app, both locally and remotely, and is therefore ideal also for unattended structures.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

WEATHER STATION PLUS KNX

Measurement and evaluation of weather data: Wind speed, Wind direction, Precipitation, Brightness, Global radiation Twilight, Temperature, Relative air humidity and Air pressure
– Installation on the outside of buildings, preferable in the roof and facade area
– Operation with additional power supply Product characteristics
– Integrated GPS/GLONASS receiver for automated positioning
– Calculation of additional weather data: Absolute air humidity, chill temperature, comfort
– Function for shading control
– Integrated KNX bus coupling unit
– Measurement data acquisition and limit value monitoring
– Software logic modules for linking events
– Integrated heating

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]