Posted on

TRANSPONDER READER KNX

The Transponder Reader TR32Ax9KNX is 2 IN / 2 OUT + BELL and a KNX wall mounting device suitable to access control application.
This device can be used in any kind of building (Hotel, Hospital, Offices, Parking, etc..) where the access control application is required.
The device is equipped with two binary inputs (potential free contacts) that can be used, for instance, to control whether the door lock has been opened or closed or other signals coming from external switches/contacts (i.e. windows, bathroom emergency alarms, etc..) and with one frontal switch freely configurable by ETS. The transponder reader is equipped also with two output relays which can be used for any purposes, typically to open the door or turning on the courtesy light inside the room.
The product provides on the front side four LEDs in order to enlighten 4 icons to display the following states (e.g. in case of Hotel management):
– Access Allowed/Not Allowed
– SOS request
– Service Call (clean room, etc..)
– Client status (“Busy room” or “Do not Disturb”)
The LEDs and icons can be configured in association with other alarms or events. The transponder reader can reads cards or keys at a maximum distance of 30mm from the front side.
The access control follows a sequence where the “build number” has been checked at first, then the “data” to check if it has been elapsed or not, next the password ID for client/ guest/service identification, then the enabled entrance timing window. In case card reading pass all checks the door is opened and, if set, the courtesy light inside is switched on. At the same time the Transponder Holder can send the reading response to the bus.
The device configuration for commissioning in terms of physical address, group addresses and parameters is done with ETS ( Engineering Tool Software) through a download of the Application Program.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

Posted on

DA110 Dali Gateway by Eelectron

DA100 KNX-DALI Gateway operates between KNX and DALI bus. DALI power supply is integrated in the device. DA110 differs from DA100 by its ability to individually control each DALI load. DA110 is compliant with IEC 62386 standard.

General Specifications

Up to 64 DALI devices connectable to DALI Bus (Fluorescent-ECG, LED driver)

Used with EAE DALI Commissioning Tool for DALI operations (addressing, grouping etc.)

Individual load control and 16 lighting scenes

Monitoring Fault status of DALI devices using different KNX group objects

Contact: +923312887178

Posted on

HRS – Hotel Room Supervisor by Eelectron

Instead of using Power Supply and IP Router for each rooms, you will be just providing Hotel Room Supervisor and each rooms of the hotels will be able to reach IP line seperately. It saves significant cost per room. Device also makes you able to have occupancy based controls for energy saving with its logic functions. In this case, you will be able to remove card holder from the system and this is optional.

General Specifications

  • Modbus TCP to KNX gateway provides all room control and monitoring requirements for hotel management and SCADA systems.
  • Gateway can map up to 1000 KNX group addresses
  • Built-in 320mA KNX bus power supply with auxiliary 30V output
  • Patent pending card holder-less room presence detection feature
  • Easy and remote commissioning via IP network
  • Optional physical inputs for door, window and presence sensors
  • Optional room energy measurement and reporting
  • Optional time sensitive scene selection with RTC
  • When the guest is not in the room, it guarantees energy saving without using the cardholder (energy saver)
  • 4 separate scenarios ; Pre-Welcome, Welcome, leave and check-out
  • Saving the configurations of guests and calling configurated scenarios.
  • Scenarios defined in the room can be changed through the GRMS software .
  • It has 3 dry contact inputs for ; Doors, Windows and Presence
Posted on

Rosa Crystal KNX Touch Switches

Rosa Crystal switches are designed for the needs of modern buildings. The new generation of frameless design was designed according to the expectations of the architects. Elegant and trendy touch with glass design in your interior!

Touch sensitivity…

Touch sensitivity switch with one to six equal surfaces, each with its own functions.
Superior touch function!

Glass Surface…

The Rosa Crystal family consists of a 4 mm tampered glass surface covered with conductive material. This allows for a safe operation as well as an elegant appearance.

Frameless minimalist design…

Modern look with 85 x 85mm frameless design

Wide range of colors…

Black and white color options as well as optional RAL cardela colors can be preferred.

Modes…

Away, comfort, night and protection mode options

Customize icon options…

With a glass surface, Rosa offers an unique user experience and intuitive operation with minimalist icon design.
Various icon options make it easy to use.

Independent programmable buttons…

Short – long press options on all buttons.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

Rosa Metal KNX Switches by EAE

With its brushed metal surface, Rosa Metal switches continue to add value to your space with the frameless design. Rosa; touch design and minimalist icon options provide a unique user experience.

Touch operated…

Rosa switches provide an aesthetic appearance and ease of use with large and brushed surface buttons. Perfect touch even from corners!

Brushed metal surfaces…

Brushed metal surfaces adds aesthethic apperance to your space. Rosa brushed metal switches contain 5 different color alternatives. (Pearl White, Natural, Gold, Bronze, Anthracite)

Customize icon options…

User-friendly icons and custom designs help users know the functions of the buttons.

Wide range of colors…

Rosa Metal switch has a choice of 5 different color metal surfaces ranging up to 3 folds.

Pearl White
Natural
Gold
Bronze
Anthracite

Feedback LEDs…

Whereby the feedback LEDs in Rosa’s unique design, you can monitor the status of lighting, curtains / blinds and air conditioners in your living spaces at a glance.

Navigation LED…

Reach your switches quickly and safely with the navigation leds in Rosa.
Light up Rosa in the dark!

Frameless design…

85 x 85 mm frameless design

Independent programable buttons…

Short – Long Press Options…

High quality raw materials…

We are using 7000 series aluminium for our Rosa switch & thermostat.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

20 Channel Lighting Control Relay by EAE

EAE Room Controller Unit is an all-in-one KNX device to control various different room units from a single interface. Room Control Unit provides control of lights, blinds and fan coils as well as optional dry contact inputs.

General Specifications

Does not require an external power supply, 20x16A Outputs

Room Control Unit covers all requirements of control in room applications and offers following functions:

  • Light switch
  • AC/DC blind control
  • Fan control
  • Fan Coil Control (2 & 3 point valve)
  • Dry contact inputs

Switching resistive, capacitive and inductive loads in accordance with EN 60669 with following functions:

  • Staircase
  • External logic
  • Priority
  • Threshold
  • Operating hour
  • Sweep

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

SW104 – 4 Channel KNX Relay

4x16A, 500A Inrush Current

In addition to switching resistive loads, SW108 is designed to be used with capacitive and inductive loads, enabling a convenient control of fluorescent ballasts and led drivers for smart home automation

General Specification

4 independently configurable channels

Manual control for each relay on the device using slide switches

Does not require an external power supply

Electric current control can be configured

Following functions can be defined separately for each channel:

  • Stair function
  • External logic
  • Internal logic
  • Priority function
  • Threshold function
  • Transaction time
  • Sweep function

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

SW108 – 8 Channel KNX Relay

8x16A, 500A Inrush Current

In addition to switching resistive loads, SW108 is designed to be used with capacitive and inductive loads, enabling a convenient control of fluorescent ballasts and led drivers.

General Specification

8 independently configurable channels

Manual control for each relay on the device using slide switches

Does not require an external power supply

Electric current control can be configured

Following functions can be defined separately for each channel:

  • Stair function
  • External logic
  • Internal logic
  • Priority function
  • Threshold function
  • Transaction time
  • Sweep function

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

UD105 KNX Universal Dimmer EAE

General Specification

Incandescent lamp, halogen lamp, dimmable LED and fluorescent lamps can be dimmed up to 1500W in 5 parallel channels for smart home systems

Flexibility to connect loads even below 1W (LED bulbs) without any lower limit

5 independent channels that can be parameterized via ETS4/ETS5.

Manual operation feature for each channel using membrane switches.

Each channel can actualize any of these functions separately.

Following function list provided;

  • Staircase
  • Scene
  • Operating Hour
  • Forced Operation

Configurable behavior after voltage return, voltage failure or ETS download.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

KNX PRESENCE DETECTOR STANDARD WITH LIGHTING CONTROL

The KNX presence detector STANDARD (PD00E01KNX) suitable for ceiling mounting ,  manages the detection and includes a brightness sensor for environmental lighting control. The STANDARD version has a rear connector with 3 digital inputs that can be connected to buttons or switches free of potential and used for on / off commands, dimming, shutters or blinds / scenarios, sequences, step commands, etc. One of the 3 inputs can be configured as analogue for the connection of NTC temperature probes with which to send the temperature measurement on the bus or manage a complete thermostat module. The thermostat manages 2 stages with an integrated PI controller for controlling heating and cooling equipment, valves, 2 and 4-pipe fan coils, etc. Presence detection, based on a passive infrared sensor, has 5 independently configurable channels with different functions that can be activated. Moreover, 12 logic blocks are available to implement simple expressions with logical or threshold operator or complex expressions with algebraic and conditional operators; It’s possible to use predefined algorithms as proportional controls of temperature and humidity or dew point calculation. The device also integrates the “Virtual Holder Logic”; the field of application is the hotel room: through a magnetic sensor installed on the door and connected to a digital input (also to the sensor itself), accurate presence information is managed. The presence detection solution can deduce the presence of people in the room using one or more dedicated sensors. It also detects an unexpected presence and is able to differentiate more behaviors. The device manages the ambient lighting based on the measured illuminance; it is also possible to enable the logic called “Circadian Rhythm” with which brightness and color temperature are imposed on the basis of predefined curves or on the basis of the real position of the sun during the day with respect to a terrestrial coordinate. This function allows you to recreate lighting comfort in an environment as close as possible to reality.

For queries please contact below

Tel: +92-21-35250460

Cell: +92-313-8867581

Cell: +92-331-2887178

Email: [email protected]