TRANSPONDER HOLDER KNX 2 IN / 2 OUT BY EELECTRON

The TH22AxxKNX transponder holder is an EIB / KNX device fitted in rectangular boxes with 2 or 3 modules, and can be used for detecting and monitoring the presence of customers or service staff in a room.
A range of colours is available for plastic housing, and glass finishes can be ordered separately, and it can be connected to all types of environments. The device has two physical ON / OFF inputs for controlling an open / close door contact or other signals (e.g. window contacts, bathroom alarm pulls, etc.). On the device there are two relays to control the door lock and to control the ” courtesy lighting “, or for any other freely configurable use. The front of the transponder is illuminated if no light is available (for dark locations), goes out if the card is invalid, and flashes for 3 seconds if access is not allowed. Card validation is made by checking the following data: -“number system”, if the code is coherent, it verifies the “date” field (if enabled) to verify validity (if this hasn’t expired). It then checks the “password” with all the associated and enabled codes (time, customer number, service number). If all the conditions matched, then is possible to open the door and, if set, turns on the courtesy light and sends the result to the bus. Configuration via ETS.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

EXTERNAL TRANSPONDER READER

The TR22A11KNX from Eelectron is a external card reader is an EIB/KNX device dedicated to access control. This product is for both 2 modules round and squared inwall boxes or for 3 modules boxes, the plexiglass front of the product is available in two different colours. The device has two physical binary inputs available for controlling the door open / close contacts or freely configurable by the user (window contacts, bathroom pull alarms etc.). The device has two relays for lock management, courtesy light control or another use. On the reader front there are 4 LEDs, 3 of which are freely configurable, usually programmed to report about: access granted, access denied, emergency, make up room, room occupied or do not disturb.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

TRANSPONDER READER KNX

The Transponder Reader TR32Ax9KNX is 2 IN / 2 OUT + BELL and a KNX wall mounting device suitable to access control application.
This device can be used in any kind of building (Hotel, Hospital, Offices, Parking, etc..) where the access control application is required.
The device is equipped with two binary inputs (potential free contacts) that can be used, for instance, to control whether the door lock has been opened or closed or other signals coming from external switches/contacts (i.e. windows, bathroom emergency alarms, etc..) and with one frontal switch freely configurable by ETS. The transponder reader is equipped also with two output relays which can be used for any purposes, typically to open the door or turning on the courtesy light inside the room.
The product provides on the front side four LEDs in order to enlighten 4 icons to display the following states (e.g. in case of Hotel management):
– Access Allowed/Not Allowed
– SOS request
– Service Call (clean room, etc..)
– Client status (“Busy room” or “Do not Disturb”)
The LEDs and icons can be configured in association with other alarms or events. The transponder reader can reads cards or keys at a maximum distance of 30mm from the front side.
The access control follows a sequence where the “build number” has been checked at first, then the “data” to check if it has been elapsed or not, next the password ID for client/ guest/service identification, then the enabled entrance timing window. In case card reading pass all checks the door is opened and, if set, the courtesy light inside is switched on. At the same time the Transponder Holder can send the reading response to the bus.
The device configuration for commissioning in terms of physical address, group addresses and parameters is done with ETS ( Engineering Tool Software) through a download of the Application Program.

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

TRANSPONDER KEYHOLDER

Dimensions and characteristics of Key chains
Dimensions and Material: ABS 38 x 34 x 6 mm
Frequency: 125KHz –
Operational temperature: -10 ° C to 50 ° C
50 PCS

We are proud to have the best smart home and building automation products in Pakistan.

Tel: +92-21-35250460

Cell: +92-330-6322277

Cell: +92-331-2887178

Email: [email protected]

HRS – Hotel Room Supervisor by Eelectron

Instead of using Power Supply and IP Router for each rooms, you will be just providing Hotel Room Supervisor and each rooms of the hotels will be able to reach IP line seperately. It saves significant cost per room. Device also makes you able to have occupancy based controls for energy saving with its logic functions. In this case, you will be able to remove card holder from the system and this is optional.

General Specifications


  • Modbus TCP to KNX gateway provides all room control and monitoring requirements for hotel management and SCADA systems.
  • Gateway can map up to 1000 KNX group addresses
  • Built-in 320mA KNX bus power supply with auxiliary 30V output
  • Patent pending card holder-less room presence detection feature
  • Easy and remote commissioning via IP network
  • Optional physical inputs for door, window and presence sensors
  • Optional room energy measurement and reporting
  • Optional time sensitive scene selection with RTC
  • When the guest is not in the room, it guarantees energy saving without using the cardholder (energy saver)
  • 4 separate scenarios ; Pre-Welcome, Welcome, leave and check-out
  • Saving the configurations of guests and calling configurated scenarios.
  • Scenarios defined in the room can be changed through the GRMS software .
  • It has 3 dry contact inputs for ; Doors, Windows and Presence

Rosa Crystal KNX Touch Switches

Rosa Crystal switches are designed for the needs of modern buildings. The new generation of frameless design was designed according to the expectations of the architects. Elegant and trendy touch with glass design in your interior!

Touch sensitivity…

Touch sensitivity switch with one to six equal surfaces, each with its own functions.
Superior touch function!

Glass Surface…

The Rosa Crystal family consists of a 4 mm tampered glass surface covered with conductive material. This allows for a safe operation as well as an elegant appearance.

Frameless minimalist design…

Modern look with 85 x 85mm frameless design

Wide range of colors…

Black and white color options as well as optional RAL cardela colors can be preferred.

Modes…

Away, comfort, night and protection mode options

Customize icon options…

With a glass surface, Rosa offers an unique user experience and intuitive operation with minimalist icon design.
Various icon options make it easy to use.

Independent programmable buttons…

Short – long press options on all buttons.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]