Posted on

SW104 – 4 Channel KNX Relay

4x16A, 500A Inrush Current

In addition to switching resistive loads, SW108 is designed to be used with capacitive and inductive loads, enabling a convenient control of fluorescent ballasts and led drivers for smart home automation

General Specification

4 independently configurable channels

Manual control for each relay on the device using slide switches

Does not require an external power supply

Electric current control can be configured

Following functions can be defined separately for each channel:

  • Stair function
  • External logic
  • Internal logic
  • Priority function
  • Threshold function
  • Transaction time
  • Sweep function

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

UD105 KNX Universal Dimmer EAE

General Specification

Incandescent lamp, halogen lamp, dimmable LED and fluorescent lamps can be dimmed up to 1500W in 5 parallel channels for smart home systems

Flexibility to connect loads even below 1W (LED bulbs) without any lower limit

5 independent channels that can be parameterized via ETS4/ETS5.

Manual operation feature for each channel using membrane switches.

Each channel can actualize any of these functions separately.

Following function list provided;

  • Staircase
  • Scene
  • Operating Hour
  • Forced Operation

Configurable behavior after voltage return, voltage failure or ETS download.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

KNX PRESENCE DETECTOR STANDARD WITH LIGHTING CONTROL

The KNX presence detector STANDARD (PD00E01KNX) suitable for ceiling mounting ,  manages the detection and includes a brightness sensor for environmental lighting control. The STANDARD version has a rear connector with 3 digital inputs that can be connected to buttons or switches free of potential and used for on / off commands, dimming, shutters or blinds / scenarios, sequences, step commands, etc. One of the 3 inputs can be configured as analogue for the connection of NTC temperature probes with which to send the temperature measurement on the bus or manage a complete thermostat module. The thermostat manages 2 stages with an integrated PI controller for controlling heating and cooling equipment, valves, 2 and 4-pipe fan coils, etc. Presence detection, based on a passive infrared sensor, has 5 independently configurable channels with different functions that can be activated. Moreover, 12 logic blocks are available to implement simple expressions with logical or threshold operator or complex expressions with algebraic and conditional operators; It’s possible to use predefined algorithms as proportional controls of temperature and humidity or dew point calculation. The device also integrates the “Virtual Holder Logic”; the field of application is the hotel room: through a magnetic sensor installed on the door and connected to a digital input (also to the sensor itself), accurate presence information is managed. The presence detection solution can deduce the presence of people in the room using one or more dedicated sensors. It also detects an unexpected presence and is able to differentiate more behaviors. The device manages the ambient lighting based on the measured illuminance; it is also possible to enable the logic called “Circadian Rhythm” with which brightness and color temperature are imposed on the basis of predefined curves or on the basis of the real position of the sun during the day with respect to a terrestrial coordinate. This function allows you to recreate lighting comfort in an environment as close as possible to reality.

For queries please contact below

Tel: +92-21-35250460

Cell: +92-313-8867581

Cell: +92-331-2887178

Email: [email protected]

Posted on

PUSH BUTTON INTERFACE by Eelectron

The device is dedicated to interface dry contacts with 2,4 or 6 input channels, such as sensors, conventional push buttons and 2 or 4 low voltage/current output channels to drive LED signal indicator lamps. These devices are extremely compact size (only 34 x 34 x 11 mm) and can also be used in installations where the in wall space available is reduced. The digital inputs can interface sensors, traditional buttons, etc; the 4 low- voltage output channels can drive LEDs for synoptic panels or switches. Outputs can drive low voltage LED; if possible use high-efficiency LED Eelectron cod. LD00A01ACC (blue color) or LD00A11ACC (white color). There are also 8 blocks of logic functions freely configurable by ETS (6 blocks available on IO62D01KNX). Device is equipped with KNX communication interface.

Posted on

UNIVERSAL DIMMER 2 CHANNELS X 300W by Eelectron

DM02A02KNX is a universal KNX 2 channel dimmer with automatic identification of the type of load and with adjustable parameters to optimize the control of different types of lamps such as LEDs, incandescent and halogen lamps, dimmable compact fluorescent lamps (CFL), low voltage lamps with electronic or ferromagnetic transformer.
The 2 channels can be used independently or combined to drive higher power loads; always respect the maximum power values indicated in the table of this instruction sheet and check in the handbook how to configure the outputs as combined in ETS. To define the maximum load and in particular the maximum number of lamps that can be connected, the DimmerLoadTester software is available; with it is possible to analyze the peak absorption of a single lamp and calculate the maximum number of lamps that can be connected.
Each output channel can be used in the following configurations:

Trailing Edge [RC]: The dimmer turns off part of the final part of the waveform of the input voltage resulting in reduced lamp output. This load regulation is used for resistive or capacitive loads (typically halogen lamps with electronic transformer or incandescent lamps)

Leading Edge [L]: The dimmer turns off part of the initial part of the waveform of the input voltage, resulting in reduced lamp output. This load regulation is used for inductive loads (typically ferromagnetic transformers or toroidal)

For queries please contact below

Tel: +92-21-35250460

Cell: +92-313-8867581

Cell: +92-331-2887178

Email: [email protected]

Posted on

16 Channel KNX Relay by Eelectron

Device  BO16F01KNX is a DIN rail EIB / KNX actuators with 16 relay outputs that canbe configured as:

– 16 outputs for light / load control
–  16 channels for valve in PWM (solenoid actuators)
–  8 channels for roller shutter / venetian control
–  8 channels for 3-point valve control
–  4 fan coil actuators 2-pipes
It is also possible to combine 2 or 3 relays with logic interlock for 4-pipe / 3-speed fan coil control or combine groups of relays (up to 8) for special function using logic interlock .

Version BO16F01KNX-SD includes a microSD card reader with which you can save the programming of the device to be able to restore it on an identical device in order to avoid programming in field or to allow a fast restore in case of failure.

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

12 Channel KNX Relay by Eelectron

BO12B01KNX is a Din Rail 12 output 16 A actuator and can be used to:


• Control up to 12 independent loads / lights
• Control up to 6 independent blind / roller shutters with mechanical end position Device is intended to be installed on DIN rail. Used in smart home automation

We are proud to have the best building automation products in Pakistan.

Cell: +92-330-8867589

Cell: +92-331-2887178

Tel: +92-21-35250460

Email: [email protected]

Posted on

UNIVERSAL DIN MODULE 4 OUTPUTS PLUS by Eelectron

Device BO04F01KNX is a DIN rail EIB / KNX actuators with 4 relay outputs that canbe configured as:

– 4 outputs for light / load control
–  4 channels for valve in PWM (solenoid actuators)
–  2 channels for roller shutter / venetian control
–  2 channels for 3-point valve control
–  1 fan coil actuators 2-pipes

Version BO04F01KNX-SD includes a microSD card reader with which you can save the programming of the device to be able to restore it on an identical device in order to avoid programming in field or to allow a fast restore in case of failure.

Posted on

UNIVERSAL DIN MODULE 8 OUT PLUS by Eelectron

Device BO08F01KNX is a DIN rail EIB / KNX actuators with 8 relay outputs that can be configured as:

–  8 outputs for light / load control
–  8 channels for valve in PWM (solenoid actuators)
–  4 channels for roller shutter / venetian control
–  4 channels for 3-point valve control
–  2 fan coil actuators 2-pipes
It is also possible to combine 2 or 3 relays with logic interlock for 4-pipe / 3-speed fan coil control or combine groups of relays (up to 8) for special function using logic interlock .

Version BO08F01KNX-SD  includes a microSD card reader with which you can save the programming of the device to be able to restore it on an identical device in order to avoid programming in field or to allow a fast restore in case of failure.